• Home
  • DIY
    • Self build
    • Projects and advice
      • Bathroom
      • Building, brickwork and masonry
      • Ceilings
      • Cleaning
      • Concrete work
      • Damp, rot and infestation
      • Drains
      • Electrical
      • Fireplaces
      • Floors
      • Garden
      • Heating
      • Insulation
      • Kitchen
      • Lighting
      • Lofts
      • Painting and decorating
      • Plasterwork
      • Plumbing
      • Roof and guttering
      • Safety
      • Security
      • Tiling
      • Walls
      • Windows
      • Woodwork
    • Glossary
    • Know your tools
    • Know your materials
  • Cost guides
  • News
  • Community
Facebook Twitter Instagram
lets-do-diy.com
  • Home
  • DIY
    • Self build
    • Projects and advice
      • Bathroom
      • Building, brickwork and masonry
      • Ceilings
      • Cleaning
      • Concrete work
      • Damp, rot and infestation
      • Drains
      • Electrical
      • Fireplaces
      • Floors
      • Garden
      • Heating
      • Insulation
      • Kitchen
      • Lighting
      • Lofts
      • Painting and decorating
      • Plasterwork
      • Plumbing
      • Roof and guttering
      • Safety
      • Security
      • Tiling
      • Walls
      • Windows
      • Woodwork
    • Glossary
    • Know your tools
    • Know your materials
  • Cost guides
  • News
  • Community
lets-do-diy.com
You are at:Home»Projects and advice»Fitting an outside tap

Fitting an outside tap

Summary: Learn how to fit an outside tap, install a branch pipe, extend the branch outside and attach a tap.


Before commencing work you must notify your water company, as the installation of an outdoor tap will result in an increase in your water rates. A double check-valve must be fitted as close to the tap as possible to prevent the risk of back-siphonage. If the tap will be fitted close to any outside wall ensure the tap has an angled head to prevent grazed knuckles whenever you turn it on and off.

This project looks at installing an outdoor tap using a copper pipe running off a 15mm (3/5in) rising main, which enters the house through the kitchen and connects to the kitchen taps.

It is advisable to fit a stop tap to the branch pipe running from the rising main, in order to turn off the water and drain the branch pipe for the winter. This will also allow you to complete the installation in two phases.


Measuring out

  • Position the tap on the outside wall of the kitchen, close to the rising main and at least 250mm (10in) above the damp-proof course. Also ensure you can place a bucket under the tap.
  • Mark the tap position on the wall
  • About 150mm (6in) above the tap make another mark indicating the position for the hole.
  • Measure the distance between the position of the hole and a window or other feature and transfer this measurement onto the inside wall. Check that the position of the hole, through which you will feed the branch pipe, is above the main stop-tap on the rising main and that the branch pipe will not be in the way of any other fittings. When satisfied with the position of the hole, mark it with a ‘cross’ on the wall.

Installing the branch pipe

  • Drill holes through the side of the unit accommodating the sink to allow the appliance’s hoses to feed through and connect to the pipes.
  • Turn off the hot and cold water supply to the kitchen.
  • You need to fit Tee valves into the supply pipes at a suitable height for connecting to the appliance. Make two marks 20mm (4/5 in) apart on the cold water supply pipe. Repeat this process on the hot water supply pipe.
  • Then using a pipe slice or hacksaw cut squarely through the pipes. It is best to cut at the lower mark first. When the sections of pipes have been removed file the end of the pipes smooth.
  • Slip the capnuts and olives of the T-valves onto the pipes. To prevent the capnuts and olives slipping off the upper lengths of pipe, attach a spring-clip clothes peg to the pipes.
  • Insert the Tee valve into each of the cut out sections. Using a spanner or wrench tighten the collars which grip the olives, but do not over-tighten.
  • Once the Tee valves are connected to both ends of the supply pipes, a small length of pipe can be fitted to the remaining Tee valve opening, which in turn will be connected to a check valve.
  • Valves with colour-coded taps for hot and cold supply pipes can now be fitted into the check valves. The colour-coded taps should point towards the appliance.
  • Feed the washing machine’s hoses through the holes you have made in the side of sink unit and, after checking the black rubber washer is inside the plastic nut of the hose, screw them onto the appropriate valves.
  • The other ends of the hoses can now be attached to the appliance. Turn on the water and check for leaks.

Extending the branch outside

Beginning with a slim masonry bit, drill through the wall from the inside at the point you marked earlier.
  • Drill through the wall from the inside at the point you marked earlier. Use a heavy-duty power drill (these can be hired) with a masonry bit at least 325mm (13in) long. You may want to use a very slim masonry bit to begin to allow you to drill through the wall much quicker. 
  • Then drill through the hole again with a masonry bit with a diameter slightly larger than that of the pipe (at least 20mm 4/5in). Drill from both sides of the wall. Remove the bit from the hole regularly to clear debris and to let the bit cool.
  • Once the hole is drilled, cut a section of pipe to fit between the double check valve and the hole, allowing enough pipe to fit into the valve at one end and an elbow joint at the other.
  • Then cut another length of pipe to fit through the hole, leaving about 50mm (2in) excess on either end to fit into joints.
  • Using an elbow joint connect the two lengths of pipe and then slide the pipe through the hole in the wall.
  • Connect the other end to the double check valve.
  • From outside, cut down the pipe protruding from the hole to leave only 25mm (1in) projecting from the hole in the wall.
  • Connect another elbow joint to the end of pipe projecting from the wall. The free end of the elbow joint should be pointing down towards the position of the tap.
  • Cut a length of pipe to reach between the elbow joint and the position of the tap.
  • Fit one end of this length of pipe into the inlet of the wall-plate elbow joint.
  • Temporarily fit the other end of the pipe into the elbow joint connected to the pipe projecting from the wall. Holding the wall-plate firmly against the wall, mark the position of the screw holes.
  • Remove the pipe and wall-plate to drill and plug the holes.
  • Reconnect the pipe to the elbow joint projecting from the wall and screw the wall-plate elbow to the wall.

Screw the tap tail into the elbow join.

Attaching the tap

  • Wind some PTFE tape around the tail of the tap.
  • Screw the tap tail into the elbow joint.
  • If the tap spout is not pointing straight downwards when fully tightened, remove it and place thin fibre washers over the tap thread before re-tightening.
  • Turn on the new stop-tap you fitted to the branch pipeand check for leaks.
  • Seal around the pipe hole in the wall with an expanding foam filler, sealant or exterior filler.

Tools needed

  • Spirit level
  • Hacksaw or pipe slice
  • File
  • Adjustable spanner
  • Power drill
  • Masonry bit
  • Screwdriver

Materials needed

  • Tap fitting
  • Copper pipe
  • Tee valve
  • Capnut
  • Olive
  • Foam-filler, sealant
  • Wall filler
  • Elbow joint
  • Wall-plate elbow joint
  • Wall plugs
  • Screws
  • PTFE tape
  • Foam filler, sealant OR wall filler

Related projects

  • Bleeding a radiator
  • Burst pipe
  • How to change a tap
  • How to cut pipe
  • How to replace a bath
  • How to replace a toilet
  • How to use a pipe bender
  • Push fit fittings

Related cost guides

  • Average cost of a driveway
  • Average cost of a greenhouse
  • Average cost of a shed
  • Average cost of block paving
  • Average cost of decking
  • Average cost of landscaping
  • Average cost of a plumber
  • Average cost of soil
  • Average cost of tree removal
  • Average cost to hire a mini digger
  • Average cost to lay turf
  • Average fence installation cost
  • Average patio cost
  • Building a brick garden wall
  • Joining pipes
  • Tap repairs
Recent Comments
  • Vic on Is Christmas a good time for DIY?
  • Anonymous on Average air source heat pump cost (2022)
  • Reggie on Prepare your home for moth season
Latest News
0

Potential DIY home improvement trends for 2023

1

Is Christmas a good time for DIY?

0

Design trends for 2022 and 2023

0

Product Review: Handsaws

Popular Guides

Average stair lift cost

Average cost to lay turf

Average air source heat pump cost (2022)

Average hardwood floor cost

Popular Projects

Insulating a hot water tank

Rising damp treatment

How to bleed a radiator

Laying terracotta or quarry tiles in a diagonal pattern

DIY Categories
Bathroom
Building, brickwork and masonry
Ceilings
Cleaning
Concrete work
Damp, rot and infestation
Drains
Electrical
Fireplaces
Floors
Garden
Heating
Insulation
Kitchen
Lighting
Lofts
Painting and decorating
Plasterwork
Plumbing
Roof and guttering
Safety
Security
Tiling
Walls
Windows
Woodwork

Self Build Guide
How to find a building plot
Evaluating a building plot (2023)
How to get a self build mortgage
Self build construction options
Self build architect and design considerations (2023)
Self build planning permission and legal consents
© 2023 lets do diy ltd | ebuild
  • Home
  • About
  • Contact us

Type above and press Enter to search. Press Esc to cancel.

We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
Cookie SettingsAccept All
Manage consent

Privacy Overview

This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary
Always Enabled
Necessary cookies are absolutely essential for the website to function properly. These cookies ensure basic functionalities and security features of the website, anonymously.
CookieDurationDescription
cookielawinfo-checkbox-analytics11 monthsThis cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Analytics".
cookielawinfo-checkbox-functional11 monthsThe cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional".
cookielawinfo-checkbox-necessary11 monthsThis cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category "Necessary".
cookielawinfo-checkbox-others11 monthsThis cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other.
cookielawinfo-checkbox-performance11 monthsThis cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Performance".
viewed_cookie_policy11 monthsThe cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. It does not store any personal data.
Functional
Functional cookies help to perform certain functionalities like sharing the content of the website on social media platforms, collect feedbacks, and other third-party features.
Performance
Performance cookies are used to understand and analyze the key performance indexes of the website which helps in delivering a better user experience for the visitors.
Analytics
Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics the number of visitors, bounce rate, traffic source, etc.
Advertisement
Advertisement cookies are used to provide visitors with relevant ads and marketing campaigns. These cookies track visitors across websites and collect information to provide customized ads.
Others
Other uncategorized cookies are those that are being analyzed and have not been classified into a category as yet.
SAVE & ACCEPT